Diseño de arrays de antenas reconfigurables alimentados por redes corporativas en guía de onda con tornillos de ajuste
Author
Villena Medina, RaquelAdvisor
Sánchez Olivares, PabloEntity
UAM. Departamento de Tecnología Electrónica y de las ComunicacionesDate
2017-06Subjects
Red de alimentación corporativa; Guía de onda; Plano H; TelecomunicacionesNote
Máster Universitario en Ingeniería de TelecomunicaciónEsta obra está bajo una licencia de Creative Commons Reconocimiento-NoComercial-SinObraDerivada 4.0 Internacional.
Abstract
Este Trabajo Fin de Máster ha tenido como objetivo la realización de una antena
reconfigurable de una entrada y cuatro salidas con una red corporativa en guía de onda
rectangular, bajo el estándar WR-51 en el plano H. El control dinámico de amplitud y
fase ha sido implementado mediante la introducción de tornillos convencionales o
tornillos de ajuste dentro de la estructura de la red. La banda de frecuencias de trabajo
comprende desde los 16GHz hasta los 18GHz (banda Ku).
Fijando la posición de los tornillos de ajuste dentro de la estructura de la red se consiguen
distintos desfases, de tal forma que se modifique la fase con la que llega la señal del
divisor a cada una de las salidas, tratando de no modificar el reparto de potencia a cada
una de ellas.
Se han tomado dos puntos de referencia en este trabajo. El primero de ellos ha sido un
divisor en guía de onda WR-51 de 1 entrada y 2 salidas, en el cual se ha conseguido
reducir su tamaño y acercar las salidas entre sí manteniendo la posición de los tornillos
en la medida de lo posible para realizar un divisor 1 a 4. El segundo se basa en un divisor
de una entrada y cuatro salidas ya diseñado en, igualmente, WR-51, en el cual se han
buscado nuevas configuraciones de tornillos. En ambos diseños se ha llevado a cabo un
análisis de configuración de la red corporativa, así como la implementación de la antena
y su simulación para las distintas configuraciones de tornillos.
Se ha realizado la construcción del segundo diseño tras obtener valores de simulación
favorables y se ha realizado una comparativa entre simulación y medida. Las medidas
han sido tanto de la red como de la antena completa utilizando el analizador de redes y la
cámara anecoica del grupo RFCAS en la Escuela Politécnica Superior (UAM). The aim of this project is the realization of a reconfigurable antenna of one input and four
outputs with a corporate network in rectangular waveguide, under standard WR-51 in
plane H. The control of the amplitude and phase has been through the introduction of
conventional screws or adjustment screws into the network structure. The band of
frequencies of the electromagnetic spectrum in which it has been worked is the band Ku,
that includes from the 16GHz to the 18GHz.
By fixing the position of the adjusting screws within the network structure different phase
is achieved on each of the outputs of the waveguide, but trying not to modify the
distribution of power signal to each of them.
Two benchmarks have been taken in this work based in some other projects in RFCAS
researching group. The first of these has been a 1-input and 2-outputs WR-51 waveguide
divider, in which it has been possible to reduce its size and to bring the outputs closer
together by maintaining the position of the screws as far as possible to make a divider 1
to 4. The second one is based on a divider of one input and four outputs already designed
in also WR-51, in which new configurations of screws have been provided. In both
designs, a configuration analysis of the corporate network has been carried out, as well
as the implementation of the antenna and its simulation for the different configurations of
screws.
The construction of the second design was carried out after obtaining favorable simulation
values and a comparison was made between simulation and measurement. The
measurement has been in both: network and radiation. It has been used the network
analyzer and the Anechoic chamber of the RFCAS group in Escuela Politécnica Superior
(UAM).
Files in this item
Google Scholar:Villena Medina, Raquel
This item appears in the following Collection(s)
Except where otherwise noted, this item's license is described as https://creativecommons.org/licenses/by-nc-nd/4.0/
Related items
Showing items related by title, author, creator and subject.
-
Diseño de antenas de parches sobre guía rectangular y tornillos de sintonía
Villena Medina, Raquel
2015-07 -
Diseño de redes de alimentación en guía de onda corporativa con tornillos de ajuste
Fernández Romero, Gema María
2016-06