Experimental analysis of 3-D sweeping wings

Download

index.pdf

Date

2015

Author

Çakır, Hasan

Metadata

Show full item record

Item Usage Stats

187
views

116
downloads

The aim of this thesis is to modify the mechanism, which is capable of mimicking the insect flight and developed previously by the Aerospace Engineering Department, and to measure the forces and moments of three types of flapping wings fixed to this mechanism. The flapping wing design is a new research topic, comparably young area and can be the future for micro unmanned air vehicles. Time varying force and moment data obtained from the experiments conducted in water as part of this thesis can be used to determine which wing geometry can be chosen for different pitch and sweep angles. A sensor measuring even very small forces and moments simultaneously in 3 axis is employed in this mechanism. Before the experiments, various birds and mechanisms are investigated and a bird wing geometry has been chosen to compare its aerodynamic features with the other geometries. Furthermore, in order to improve the mechanism and to find out the best mechanism mimicking the hummingbird flight, various test setups was studied. A connector has been designed between the mechanism and the sensor in order to minimize errors. And also this connector let us measure the pitch angle precisely whereas the old mechanism was able to measure only an approximate pitch angle. Additionally a roller bearing has been located at the center of the gear in order to transfer the power efficiently. A program which is called as “Wing-Sim” is used to control motor drivers and wings. Totally, 21 cases have been performed with three type of wings whose names are Flat Plate, Hummingbird and Zimmermann. The period of each case is 10 seconds and every cases have 50 periods. The wings have approximately the same size with each other which are 26 cm span, 7.9 cm chord and 3 mm thickness. Moreover, experimental uncertainties associated with low level fluid dynamic force measurements are addressed in this study. A drastic increase in drag force is observed after 30º pitch angle while lift force is not changed. The most efficient wing is the Zimmermann with its high L/D ratios.

Subject Keywords

Vehicles, Remotely piloted., Flying-machines., Aerodynamics., Biomimicry.

URI

http://etd.lib.metu.edu.tr/upload/12619080/index.pdf
https://hdl.handle.net/11511/24935

Collections

Graduate School of Natural and Applied Sciences, Thesis

Suggestions

OpenMETU
Core

Development and testing of a 3 DOF tandem flapping wing mechanism Mutlu, Talha; Kurtuluş, Dilek Funda; Department of Aerospace Engineering (2014) Scope of the thesis is to develop a tandem flapping wing mechanism, capable of mimicking the insect flight, in order to investigate the 3-D complex nature of the flow around the flapping wings. Thus, valuable data about the unsteady aerodynamics of such flow can be obtained in order to provide necessary knowledge for development of future Micro Air Vehicles (MAVs). The mechanism is equipped with a state of art multi axial force and torque sensor. By placing the sensor to the root chord of the wing, any forc...
Aerodynamic design and control of tandem wing unmanned aerial vehicle Kaya, Taşkın; Özgen, Serkan; Department of Aerospace Engineering (2019) This thesis presents an approach towards the design methodology of electrical propulsion, tandem wing unmanned aerial vehicle. Due to its possible rewarding features, tandem wing design is investigated as the main subject of this study. The stability and control characteristics of tandem wing aircraft are critical since the interference between the two wings may result in nonlinear aerodynamic characteristics for varying angles of attack. Thus, the design of the controller system requires careful handling, ...
Numerical and experimantal analysis of flapping motion Sarıgöl, Ebru; Alemdaroğlu, Hüseyin Nafiz; Department of Aerospace Engineering (2007) The aerodynamics of two-dimensional and three-dimensional flapping motion in hover is analyzed in incompressible, laminar flow at low Reynolds number regime. The aim of this study is to understand the physics and the underlying mechanisms of the flapping motion using both numerical tools (Direct Numerical Simulation) and experimental tools (Particle Image Velocimetry PIV technique). Numerical analyses cover both two-dimensional and three-dimensional configurations for different parameters using two differen...
Aerodynamic and structural design and analysis of an electric powered mini UAV Demircan, Alpay; Kayran, Altan; Department of Aerospace Engineering (2016) The aim of this study is to describe the aerodynamic and structural design of an electric powered portable Mini UAV. Conceptual design, structural design and analysis of the wing and detail design phases of the UAV are presented in the study. Fixed wing mini UAV configuration with fixed – pitch propeller has been chosen for the design. In order to provide multi-mission capability, payload of the UAV is designed as a replaceable mission compartment. System requirements and mission profiles of the airplane ar...
Vision-aided landing for fixed wing unmanned aerial vehicle Esin, Engin; Kutay, Ali Türker; Department of Aerospace Engineering (2016) The aim of this thesis is to design an autoland system for fixed wing unmanned aerial vehicle (UAV) to make auto landing by using position information calculated by image processing algorithms. With this ability, even if GPS is not available to be used, UAV still could make a safe automatic landing. Landing autopilot is aimed to keep UAV on a straight line with a constant flight path angle. Therefore, landing autopilot and computer vision methods are studied within the scope of this thesis. Also, to test de...

Citation Formats

H. Çakır, “Experimental analysis of 3-D sweeping wings,” M.S. - Master of Science, Middle East Technical University, 2015.