Effects of microcompounding process parameters on the properties of ABS/polyamide-6 blends based nanocomposites

Date

2008-03-05

Author

Oezkoc, Gueralp
Bayram, Göknur
Quaedflieg, Martin

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

164
views

0
downloads

Melt intercalation method was applied to produce acrylonitrile-butadiene-styrene/polyamide-6 (ABS/ PA6) blends based organoclay nanocomposites using a conical twin-screw microcompounder. The blend was compatibilized using a maleated olefinic copolymer. The effects of microcompounding conditions such as screw speed, screw rotation-mode (co- or counter-), and material parameters such as blend composition and clay loading level on the morphology of the blends, dispersibility of nanoparticles, and mechanical properties were investigated. Furthermore, corotating screws were modified to achieve elongational flow which is efficient for obtaining dispersive mixing. The morphology was examined by SEM analysis after preferential extraction of the minor phase. Subsequently, the SEM micrographs were quantitatively analyzed using image analyzer software. The morphology of the blends indicated that processing with counter-rotation at a given screw speed yielded coarser morphology than that of processed with corotation. X-ray diffraction analysis showed that highest level of exfoliation is observed with increasing PA6 content, at 200 rpm of screw speed and in corotation mode. Also, the effects of screw speed, screw rotation mode, and screw modification were discussed in terms of XRD responses of the nanocomposites. The aspect ratio of the clay particles which were measured by performing image analysis on TEM micrographs exhibited a variation with processing conditions and they are in accordance with the modulus of the nanocomposites. (c) 2007 Wiley Periodicals, Inc.

Subject Keywords

Materials Chemistry, General Chemistry, Surfaces, Coatings and Films, Polymers and Plastics

URI

https://hdl.handle.net/11511/36754

Journal

JOURNAL OF APPLIED POLYMER SCIENCE

DOI

https://doi.org/10.1002/app.27460

Collections

Department of Chemical Engineering, Article

Suggestions

OpenMETU
Core

Effect of composite preparation techniques on electrical and mechanical properties and morphology of nylon 6 based conductive polymer composites Koysuren, Ozcan; Yesil, Sertan; Bayram, Göknur (Wiley, 2006-11-05) Nylon 6/carbon black conductive composites were prepared using two different methods, masterbatch dilution and melt mixing. Their effect on the size and distribution of carbon black agglomerates in the matrix was studied in terms of electrical and mechanical properties and morphology. The electrical resistivity of composites prepared by both methods decreased with increasing filler composition. The electrical resistivity of the diluted masterbatch composites and the melt mixed composites was reduced from th...
Effect of preparation parameters on performance of dense homogeneous polycarbonate gas separation membranes Hacarlioglu, P; Toppare, Levent Kamil; Yılmaz, Levent (Wiley, 2003-10-17) The aim of this study is to determine the effect of preparation parameters on the membrane permeation mechanism and separation performances of dense homogeneous poly(bisphenol A carbonate) (PC) membranes. Blade-casting and drop-casting techniques are used for casting films from solutions with varying concentrations. Chloroform and methylene chloride are used to determine the effect of the properties of the casting solvent. Permeation measurements are done with Ar, N-2, O-2, CH4, CO2, and H, gases. The selec...
Effects of olefin-based compatibilizers on the morphology, thermal and mechanical properties of ABS/polyamide-6 blends Ozkoc, Guralp; Bayram, Göknur; Bayramli, Erdal (Wiley, 2007-04-15) In this study, commercially available epoxidized and maleated olefinic copolymers, EMA-GMA (ethylene-methyl acrylate-glycidyl methacrylate) and EnBACO-MAH (ethylene-n butyl acrylate-carbon monoxide-maleic anhydride), were used at 0, 5, and 10% by weight to compatibilize the blend composed of ABS (acrylonitrile-butadiene-styrene) terpolymer and PA6 (polyamide 6). Compatibilizing performance of these two olefinic polymers was investigated from blend morphologies, thermal and mechanical properties as a functio...
Side-chain functionalization of polystyrene with maleic anhydride in the presence of Lewis acids Kurbanova, RA; Mirzaoglu, R; Akovali, G; Rzaev, ZMO; Karatas, I; Okudan, A (Wiley, 1996-01-10) Polystyrenes with different molecular weights were chemically modified with maleic anhydride by use of certain cationic catalysts of Lewis acid type (BF3 . OEt(2), AlCl3, TiCl4, ZnCl2, FeCl3, and SnCl4) in chloroform. The effects of molecular weight of polystyrene, as well as type of Lewis acid used, on properties and structure of products were investigated. The interrelation between the molecular weight of polystyrene and content of carboxyl groups in the products was made. A direct relationship between th...
Flexible and conducting composites of polypyrrole and polydimethylsiloxane Cahmak, G; Kucukyavuz, Z; Kucukyavuz, S (Wiley, 2004-07-15) Conductive and flexible polydimethylsiloxane (PDMS)/polypyrrole (PPy) composites were synthesized electrochemically. Electrochemical syntheses were performed at +1.10 V by using p-toluene sulfonic acid (PTSA) as supporting electrolyte and water as solvent. Composites were characterized by cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, and Fourier transform infrared spectroscopy. Conductivity measurements and mechanical tests were also perform...

Citation Formats

G. Oezkoc, G. Bayram, and M. Quaedflieg, “Effects of microcompounding process parameters on the properties of ABS/polyamide-6 blends based nanocomposites,” JOURNAL OF APPLIED POLYMER SCIENCE, pp. 3058–3070, 2008, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/36754.