Effect of design and operating parameters on the thermal performance of aluminum flat grooved heat pipes

Download

index.pdf

Date

2018-03-05

Author

Alijani, Hossein
Cetin, Barbaros
Akkuş, Yigit
Dursunkaya, Zafer

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

130
views

0
downloads

Four aluminum flat grooved heat pipes with groove widths of 0.2, 0.4, 0.8 and 1.6 mm are fabricated and the effect of filling ratio on the thermal performance is experimentally studied for four different heat flux values of 2.1, 3.2, 4.2 and 5.3 W/cm(2). An optimum filling ratio corresponding to each heat flux is determined where the heat pipe has the best thermal performance. Thermal performance of the heat pipes are evaluated using three indicators: (i) the temperature difference between the heat source and heat sink surfaces, (ii) the temperature difference between the peak system temperature and the temperature of the cooling ambient and (iii) heat pipe effectiveness defined as a temperature difference ratio under dry and operating conditions. A flow and evaporative mass scaling model is developed to interpret the experimental findings. Experimental results reveal that at the optimum point the heat pipe with the 0.4 mm groove width has the best thermal performance, and the heat pipe with the smallest 0.2 mm groove operates under dryout conditions even for the lowest heat flux, the reason of which is discussed based on interpretation of underlying phase change physics. Experiments reveal the existence of two operating regimes: with and without dryout in the grooves. Although higher heat loads can be carried under dryout conditions, a limit exists for the maximum heat flux where the pipe operates without the onset of dryout for a specific groove density.

Subject Keywords

Industrial and Manufacturing Engineering, Energy Engineering and Power Technology

URI

https://hdl.handle.net/11511/46203

Journal

APPLIED THERMAL ENGINEERING

DOI

https://doi.org/10.1016/j.applthermaleng.2017.12.085

Collections

Department of Mechanical Engineering, Article

Suggestions

OpenMETU
Core

Experimental investigation of hinged and spring loaded rolling piston compressors pertaining to a turbo rotary engine OKUR, MELİH; Akmandor, Ibrahim Sinan (Elsevier BV, 2011-05-01) Hinged rolling piston compressor of a new thermodynamic cycle Pars engine promises high performance figures such as single stage high compression levels and higher volume flow discharge with competitively low input power and torque. The pumping characteristic of the present engine compressor unit has been increased by the implementation of a spring less vane configuration. The reciprocating vane which is usually operated by spring compression in air conditioning and refrigeration unit has been replaced by a...
Natural convection heat transfer from horizontal and slightly inclined plate-fin heat sinks Tarı, İlker (Elsevier BV, 2013-11-03) Natural convection from plate-fin heat sinks in both horizontal and slightly inclined from horizontal orientations is studied for the inclination angles of +/- 60 degrees, +/- 75 degrees, +80 degrees, +/- 85 degrees, +/- 90 degrees from the vertical. A set of correlations is obtained for both upward (-) and downward (+) facing horizontal cases. The correlations are tested for validity by using large sets of experimental data from literature. By varying the direction of gravitational acceleration for several...
Experimental based numerical approach for determination of volumetric heat transfer coefficients of modified graphite foams GÜRÜF, GÜRŞAH; Solmus, Ismail; BİLEN, Kadir; Bayer, Özgür (Elsevier BV, 2020-06-25) Graphite-based porous materials are emerging as attractive alternatives to metals for use as heat dissipation elements in thermal management applications. While having several desirable features such as high thermal conductivity and low density, graphite foam heat sinks also tend to have low permeability that can limit transport of working fluid within the component and result in inefficient heat transfer. In order to improve their heat dissipation performance, graphite foams can be modified by channels dri...
Performance optimization of induction motors during voltage-controlled soft starting Zenginobuz, G; Cadirci, I; Ermiş, Muammer; Barlak, C (Institute of Electrical and Electronics Engineers (IEEE), 2004-06-01) This paper deals with the performance optimization of medium/high-power induction motors during soft starting by eliminating the supply frequency torque pulsations, and by keeping the line current constant at the preset value. Starting torque pulsations are eliminated by triggering back-to-back-connected thyristors at proper points on the first supply voltage cycle. Line current during starting can be kept constant at any preset value by a simple strategy composed of successive cosinusoidal and constant fun...
Effect of Midsynthesis Addition of Silica to the Synthesis Medium on the Properties of MFI-Type Zeolite Membranes Soydas, Belma; Kalıpçılar, Halil; Culfaz, Ali (American Chemical Society (ACS), 2010-06-02) Thin zeolite membranes of MFI type were prepared on alpha-Al2O3 supports by midsynthesis addition of silica in a recirculating flow system at 95 degrees C The synthesis was started with the batch composition of 80SiO(2): 30TPAOH:1500H(2)O which was changed to 80SiO(2)center dot 9TPAOH:1500H(2)O by addition of silica Mkt 24, 48, or 72 h Compared to synthesis at constant composition. it is possible to affect the rates of nucleation and crystal growth to obtain membranes with better quality by changing the ove...

Citation Formats

H. Alijani, B. Cetin, Y. Akkuş, and Z. Dursunkaya, “Effect of design and operating parameters on the thermal performance of aluminum flat grooved heat pipes,” APPLIED THERMAL ENGINEERING, pp. 174–187, 2018, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/46203.