The effect of strain rate and temperature on forming limit diagram for DKP-6112 and AZ31 materials

Download

1-s2.0-S2351978920312579-main.pdf

Date

2020-01-01

Author

Goksen, Seckin
Darendeliler, Haluk

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

177
views

24
downloads

Forming limit diagrams (FLDs) are used in sheet metal operations widely for predicting blank fracture and forming characteristics of materials. There are three approaches for building forming limit diagrams which are the experimental, theoretical and numerical methods. Experimental method, which includes Nakazima formability test, is generally preferred for determining forming limit diagrams, although it requires complex experimental setup and effort. This study, firstly, compares the experimentally determined FLD results with the numerically obtained ones by using the constitutive models formed through the use of von Mises criteria with isotropic, kinematic and combined hardening models, and Hill48 yield criterion at quasi-static loading and room temperature conditions. The stress-strain relations are obtained by applying the Johnson-Cook phenomenological model for DKP-6112 and AZ31 materials. Then, the constitutive relation that gives closest results to experimental data is chosen to evaluate the effects of the variations of strain rate and temperature values on the FLDs for both materials. Nakazima tests, with 8 different blank specimens, are simulated by using a finite element software to present and compare the numerical forming limit diagrams. For determining the necking time in numerical FLDs maximum strain acceleration strain localization method is used. It is observed that forming limit diagram shifts downwards with strain rate increase and shifts upwards with temperature increase for both materials.

Subject Keywords

Forming limit diagram, Formability, Strain rate, Temperature

URI

https://hdl.handle.net/11511/56356

DOI

https://doi.org/10.1016/j.promfg.2020.04.194

Conference Name

23rd International Conference on Material Forming

Collections

Department of Mechanical Engineering, Conference / Seminar

Suggestions

OpenMETU
Core

A layerwise approach to modeling piezolaminated plates Ertürk, Cevher Levent; Tekinalp, Ozan; Department of Aerospace Engineering (2005) In this thesis, optimal placement of adhesively bonded piezoelectric patches on laminated plates and the determination of geometry of the bonding area to maximize actuation effect are studied. A new finite element model, in which each layer is considered to be a separate plate, is developed. The adhesive layer is modeled as a distributed spring system. In this way, relative transverse normal and shear motion of the layers are allowed. Effect of delamination on the adhesive layer stresses is also studied and...
The stress response and onset of yield of rotating FGM hollow shafts Akis, T.; Eraslan, Ahmet Nedim (2006-11-01) An analytical model is developed to study the stress response and the yielding of rotating functionally graded hollow shafts in the framework of generalized plane strain. The modulus of elasticity and the uniaxial yield limit of the shaft material are assumed to vary radially in nonlinear forms. It is shown that different modes of plasticization may take place. Analytical expressions for the critical values of the material parameters leading to different modes of plastic deformation and the corresponding el...
A numerical study on response factors for steel wall-frame systems Arslan, Hakan; Topkaya, Cem (Wiley, 2010-11-01) A numerical investigation was undertaken to evaluate the response of dual structural systems that consisting of steel plate shear walls and moment-resisting frames. The primary objective of the study was to investigate the influence of elastic base shear distribution between the wall and the frame on the global system response. A total of 10 walls and 30 wall frame systems, ranging from 3 to 15 stories, were selected for numerical assessment. These systems represent cases in which the elastic base shear res...
The effect of strain rate and temperature on deep drawing for different constitutive relations Gökşen, Seçkin; Darendeliler, Haluk; Department of Mechanical Engineering (2019) In this study, the effects of strain rate and temperature on deep drawing process are investigated by considering different yield criteria and hardening models. For this purpose, various punch velocity and temperature values are considered using 1 mmthick DKP6112 and AZ31 sheet materials. The results are compared according to thickness strain distribution and punch force obtained by a commercial finite element software. To express constitutive relations of corresponding materials for different strain rate a...
THE INFLUENCE OF MANUFACTURING DEFECTS ON STRUCTURAL PERFORMANCE OF COMPOSITE OVERWRAPPED PRESSURE VESSELS Yurdakul, Kıvanç; Gürbüz, Rıza; Department of Metallurgical and Materials Engineering (2022-2-04) In this study, the influence of defects that are occurred in manufacturing operations of filament wound composite overwrapped pressure vessels on burst pressure is investigated experimentally. Firstly, material characterization methods such as tensile testing and fiber volume fraction testing of carbon/epoxy composite specimens are completed. Following determining of different layer configurations for small scale composite pressure vessels, manufacturing and burst testing of vessels are accomplished. Ef...

Citation Formats

S. Goksen and H. Darendeliler, “The effect of strain rate and temperature on forming limit diagram for DKP-6112 and AZ31 materials,” 2020, vol. 47, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/56356.