A new grid-making technique for moire fringe method

1996-09-01
Celik, M
Bilir, OG
Show full item record
Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
31
views
0
downloads
Mechanical Engineering, Mechanics of Materials
https://hdl.handle.net/11511/64545
EXPERIMENTAL TECHNIQUES
Department of Mechanical Engineering, Article

Suggestions

A variational multiscale constitutive model for nanocrystalline materials
Gürses, Ercan (Elsevier BV, 2011-03-01)
This paper presents a variational multi-scale constitutive model in the finite deformation regime capable of capturing the mechanical behavior of nanocrystalline (nc) fcc metals. The nc-material is modeled as a two-phase material consisting of a grain interior phase and a grain boundary effected zone (GBAZ). A rate-independent isotropic porous plasticity model is employed to describe the GBAZ, whereas a crystal-plasticity model which accounts for the transition from partial dislocation to full dislocation m...
A STUDY ON THE YIELD STRESS OF PERLITE-FILLED HIGH-DENSITY POLYETHYLENES
OKTEM, GA; TINCER, T (Springer Science and Business Media LLC, 1993-12-01)
Four different types of high-density polyethylenes were blended with expanded perlite at different compositions. Gamma-aminopropyltriethoxysilane was applied to perlite (2 wt%) from ether and water solutions to enhance the interfacial adhesion between the polymer and the filler. It was shown that silane treatment advances the yield stress with improving dispersion and increasing the interfacial adhesion of the filler with the polymer matrix. The experimental results were then checked with the expression of ...
Utilization of Non-destructive Methods for Determining the Effect of Age-Hardening on Impact Toughness of 2024 Al-Cu-Mg Alloy
Gür, Cemil Hakan (Springer Science and Business Media LLC, 2008-12-01)
The aim of the study is to investigate the correlation between non-destructive measurements and impact toughness of 2024 Al-alloy. Following the solutionizing at 493 degrees C/1 h and water quench, the samples were aged at 190 degrees C for various periods between 0.5 h and 18 h. Hardness, impact toughness, sound velocity, and electrical conductivity were measured for each specimen group, and fracture surfaces were investigated by SEM. To focus on only the effect of precipitation, the process variables were...
A SURVEY OF FATIGUE CRACK-GROWTH LIFE ESTIMATION METHODOLOGIES
AKYUREK, T; BILIR, OG (Elsevier BV, 1992-07-01)
In this study, three fatigue crack growth life estimation methodologies are reviewed and sample calculations are made using these methodologies. Comparisons of the results with respect to the methodologies are made. Three computer codes which represent these methodologies, CRACKS IV, FAST and FATIGUE, are selected for the analyses. The estimations are also correlated to the test results.
Mechanics of dynamic contact of coated substrate and rigid cylindrical ended punch
Balci, Mehmet N.; Dağ, Serkan (Springer Science and Business Media LLC, 2019-05-01)
The dynamic contact mechanics of isotropic elastic coating bonded to homogeneous substrate was examined. The coating is indented by a sliding rigid punch of a cylindrical profile. The rigid punch moves over the coating at a steady subsonic speed. To determine contact stresses, an analytical method based on the singular integral equation technique is put forward. Governing partial differential equations are derived considering general theory of elastodynamics. The influences of dimensionless punch speed, mas...
Citation Formats
M. Celik and O. Bilir, “A new grid-making technique for moire fringe method,” EXPERIMENTAL TECHNIQUES, pp. 9–11, 1996, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/64545.
METU IIS - Integrated Information Service open@metu.edu.tr