Investigation of Au-Ag-Cu Alloy Electrodeposition to Electromechanical Systems

Date

2020-04-01

Author

Cagan, Berkay
ERDOĞAN, METEHAN
Karakaya, İshak
Yilmaz, Cemil
Yurdakul, Burak

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

203
views

0
downloads

© 2020 ECS - The Electrochemical Society.Electromechanical systems, which provide electrical power and data connection between moving terminals require high conduction and erosion resistant surfaces. Transfers of electrical power and data are accomplished by the contact of drum and brush wires. The simultaneous electrochemical deposition of desired Au-Ag-Cu alloy compositions, which can be used to coat the brush wires, was investigated in this study. In the scope of the study, the static potential and cyclic voltammetry behaviours of gold, silver and copper cyanide plating baths, as well as the mixtures of binary and ternary baths were investigated to obtain suitable amount of KCN and working potential values. SEM and EDS analyses were conducted in the characterization of coated samples.

Subject Keywords

General Engineering

URI

https://hdl.handle.net/11511/70194

DOI

https://doi.org/10.1149/09707.0485ecst

Collections

Department of Metallurgical and Materials Engineering, Conference / Seminar

Suggestions

OpenMETU
Core

EXPERIMENTAL-STUDY OF UNSTEADY FORCED-CONVECTION IN A DUCT WITH AND WITHOUT ARRAYS OF BLOCK-LIKE ELECTRONIC COMPONENTS LI, W; KAKAC, S; HATAY, FF; OSKAY, R (Springer Science and Business Media LLC, 1993-01-01) An experimental apparatus was designed, built and used to study the behavior of transient forced convection in a rectangular duct with and without barriers due to a sinusoidal heat input at the inlet. to simulate the electric heating and cooling inside the computer. A wide range of Reynolds number (400 less-than-or-equal-to Re less-than-or-equal-to 20,000) and inlet frequencies (0.01 Hz less-than-or-equal-to beta less-than-or-equal-to 0.08 Hz) was covered in this experimental study for both laminar and turb...
RECONSTRUCTION OF PERMITTIVITY AND CONDUCTIVITY PROFILES OF A DIELECTRIC SLAB IN THE TIME DOMAIN BY DESCENT METHODS ONDER, M; Kuzuoğlu, Mustafa (Institution of Engineering and Technology (IET), 1992-10-01) An optimisation approach is presented for the problem of reconstructing the permittivity and conductivity profiles of a dielectric slab from the reflected and transmitted field data. The problem is treated as an optimal control problem where the norm of the difference of measured and calculated boundary data is minimised subject to the state equation governing the system. The original constrained optimisation problem is reduced to the evaluation of stationary points of an augmented functional which is obtai...
A computational procedure for estimating residual stresses and secondary plastic flow limits in nonlinearly strain hardening rotating shafts Eraslan, Ahmet Nedim (Springer Science and Business Media LLC, 2005-03-01) A computational procedure to estimate the residual stress distributions and the limit angular speeds for avoiding secondary plastic deformation in nonlinearly strain hardening rotating elastic-plastic shafts is given. The model is based on von Mises yield condition, J(2) deformation theory and a Swift-type hardening law. The boundary value problem for the governing nonlinear differential equation is solved by a shooting method using Newton iterations with numerically approximated tangent. Solid as well as h...
Assessment of a frequency-domain linearised Euler solver for turbofan aft radiation predictions and comparison with measurements Özyörük, Yusuf (2010-03-31) This paper presents a frequency-domain computational aeroacoustics tool for predicting aft noise radiation through turbofan ducts and jets and its application to two realistic engine exhaust configurations which have been experimentally tested. The tool is based on the discretised axisymmetric form of the linearised Euler equations in conjunction with perfectly matched layer equations at the inlet and far-field boundaries using high-order finite differences. The resultant linear system of equations is inver...
An experimental study of residual fiber strains in Ti-15-3 continuous fiber composites Pickard, S.M.; Miracle, D.B.; Majumdar, B.S.; Kendig, K.L.; Rothenflue, L.; Çöker, Demirkan (Elsevier BV, 1995-01-01) A simplified experimental technique to determine the axial fiber residual strain in continuously-reinforced metal matrix composites is described. The residual fiber strains in two Ti-15V-3Cr-3Al-3Sn/SiC metal matrix composites have been measured with this technique. Residual fiber strains on the order of 0.2% are measured in the as-processed condition, and the residual stresses approach zero after testing the composite in tension to failure at room temperature. A conceptual description of the effect of tens...

Citation Formats

B. Cagan, M. ERDOĞAN, İ. Karakaya, C. Yilmaz, and B. Yurdakul, “Investigation of Au-Ag-Cu Alloy Electrodeposition to Electromechanical Systems,” 2020, vol. 97, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/70194.