Tribological properties of Ti-6Al-7Nb alloy after isothermal oxidation
Authors:
- Krzysztof Stefan Aniołek,
- Adrian Mariusz Barylski,
- Denis Osior
Abstract
The paper presents the characterization of tribological properties of the Ti-6Al-7Nb alloy before and after isothermal oxidation in different friction couples. Microscopic observations have shown that uniform oxide layers were obtained, which evenly covered the entire surface of the investigated samples. It was found that oxide layers deposited on the Ti-6Al-7Nb alloy substrate contribute to a considerable improvement of the tribological properties. The best resistance to sliding wear was shown by the layer obtained at a temperature of 600°C. It was also shown that presence of oxide layers on the surface of the Ti-6Al-7Nb alloy leads to an increase in the friction coefficient. The highest increase in the value of the friction coefficient was observed for a surface oxidized at 650°C during interaction with an Al2O3 ball. SEM observations of traces of the tribological interaction showed the presence of numerous scratches and fine wear products on the friction surface. For the non-oxidized condition, after interaction with a ball made of bearing steel 100Cr6, the presence was found of alternating, morphologically varied areas which had formed as a result of corrugation wear. Tests have shown that isothermal oxidation eliminates this disadvantageous phenomenon.
- Record ID
- USL4d9ce28a90c448a8b9801a7975231964
- Author
- Other language title versions
- Właściwości tribologiczne stopu Ti-6Al-7Nb po utlenianiu izotermicznym
- Journal series
- Tribologia, ISSN 0208-7774, e-ISSN 1732-422X
- Issue year
- 2019
- No
- 3
- Pages
- 5-12
- Publication size in sheets
- 0.40
- Keywords in Polish
- utlenianie izotermiczne, morfologia powierzchni, warstwy tlenkowe, właściwości tribologiczne
- Abstract in Polish
- W pracy przedstawiono charakterystykę właściwości tribologicznych stopu Ti-6Al-7Nb przed oraz po utlenianiu izotermicznym w różnych skojarzeniach ciernych. Obserwacje mikroskopowe wykazały, że otrzymano jednolite warstwy tlenkowe, które równomiernie pokrywały całą powierzchnię badanych próbek. Stwierdzono, że warstwy tlenkowe otrzymane na podłożu stopu Ti-6Al-7Nb prowadzą do znacznej poprawy właściwości tribologicznych. Najlepszą odpornością na zużycie ścierne cechowała się warstwa tlenkowa otrzymana w temperaturze 650°C. Wykazano ponadto, że obecność warstw tlenkowych na powierzchni stopu Ti-6Al-7Nb prowadzi do wzrostu współczynnika tarcia. Największy wzrost współczynnika tarcia zaobserwowano dla powierzchni utlenionej w temperaturze 650°C podczas współpracy z kulką Al2O3. Obserwacje SEM śladów współpracy tribologicznej wykazały na powierzchni tarcia obecność licznych rys oraz drobne produkty zużycia. Dla stanu nieutlenionego po współpracy z kulką ze stali łożyskowej 100Cr6 stwierdzono obecność naprzemianległych różnych morfologicznie obszarów powstałych w wyniku zużycia falistego. Wykazano, że utlenianie izotermiczne eliminuje to niekorzystne zjawisko.
- DOI
- DOI:10.5604/01.3001.0013.5428 Opening in a new tab
- Handle.net URL
- hdl.handle.net/20.500.12128/19699 Opening in a new tab
- Language
- eng (en) English
- File
-
- File: 1
- Tribological properties of Ti-6Al-7Nb alloy after isothermal oxidation, File Aniolek_Tribological_properties.pdf / 2 MB
- Aniolek_Tribological_properties.pdf
- publication date: 06-02-2024
- Tribological properties of Ti-6Al-7Nb alloy after isothermal oxidation, File Aniolek_Tribological_properties.pdf / 2 MB
-
- Score (nominal)
- 70
- Score source
- journalList
- Score
- = 70.0, 26-09-2023, ArticleFromJournal
- Publication indicators
- = 3
- Citation count
- 3
- Uniform Resource Identifier
- https://opus.us.edu.pl/info/article/USL4d9ce28a90c448a8b9801a7975231964/
- URN
urn:uni-kat-prod:USL4d9ce28a90c448a8b9801a7975231964
* presented citation count is obtained through Internet information analysis, and it is close to the number calculated by the Publish or PerishOpening in a new tab system.