Logout
Türkçe
Türkçe
Search
Login
OpenMETU
OpenMETU
About
About
Open Science Policy
Open Science Policy
Open Access Guideline
Open Access Guideline
Postgraduate Thesis Guideline
Postgraduate Thesis Guideline
Communities & Collections
Communities & Collections
Help
Help
Frequently Asked Questions
Frequently Asked Questions
Guides
Guides
Thesis submission
Thesis submission
MS without thesis term project submission
MS without thesis term project submission
Publication submission with DOI
Publication submission with DOI
Publication submission
Publication submission
Supporting Information
Supporting Information
General Information
General Information
Copyright, Embargo and License
Copyright, Embargo and License
Contact us
Contact us
Effects of Al and Fe additions on microstructure and mechanical properties of SnAgCu eutectic lead-free solders
Date
2014-01-21
Author
KANTARCIOGLU, A.
Kalay, Yunus Eren
Metadata
Show full item record
This work is licensed under a
Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License
.
Item Usage Stats
146
views
0
downloads
Cite This
In this study, Sn-3.5Ag-0.9Cu (wt%) lead-free solder was modified with minor additions of Al and Fe. The thermal, microstructural and mechanical behaviors after and before compositional modifications were investigated by a combined study of differential scanning calorimetry (DSC), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and shear strength measurements. EDS results and Darken-Gurry predictions indicated a high concentration of Fe substitution within the Cu6Sn5 at the solder/copper interface which induced desirable effects on undercooling and microstructure evolution. Eutectic SAC and SAC+0.05 wt% Al solder joints exhibit considerable number of brittle proeutectic phases (i.e., Ag3Sn). Proeutectic Ag3Sn formation was found to be suppressed after Fe modification. A new type of Al-Sn-Cu intermetallic compound was detected for Al added specimens. The rod-like morphology of this IMC appears to cause a sharp decrease in the shear strength of Al modified solder joints. The shear strength values for Fe modified solder joints were found to be higher in a wider composition range (0.01-0.1 wt% Fe) as compared to eutectic SAC and SAC+0.05 wt% Al.
Subject Keywords
Shear strength
,
Microstructure
,
Fe and Al modification
,
Lead free SAC alloys
URI
https://hdl.handle.net/11511/32848
Journal
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
DOI
https://doi.org/10.1016/j.msea.2013.11.025
Collections
Department of Metallurgical and Materials Engineering, Article
35
CITATIONS
35
Total citations
5
Recent citations
3.61
Field Citation Ratio
n/a
Relative Citation Ratio
Suggestions
OpenMETU
Core
Effect of Midsynthesis Addition of Silica to the Synthesis Medium on the Properties of MFI-Type Zeolite Membranes
Soydas, Belma; Kalıpçılar, Halil; Culfaz, Ali (American Chemical Society (ACS), 2010-06-02)
Thin zeolite membranes of MFI type were prepared on alpha-Al2O3 supports by midsynthesis addition of silica in a recirculating flow system at 95 degrees C The synthesis was started with the batch composition of 80SiO(2): 30TPAOH:1500H(2)O which was changed to 80SiO(2)center dot 9TPAOH:1500H(2)O by addition of silica Mkt 24, 48, or 72 h Compared to synthesis at constant composition. it is possible to affect the rates of nucleation and crystal growth to obtain membranes with better quality by changing the ove...
Effect of swaging on microstructure and tensile properties of W-Ni-Fe alloys
DURLU, NURİ; Caliskan, N. Kaan; Bor, Sakir (Elsevier BV, 2014-01-01)
The objective of this study was to investigate the effect of swaging on the microstructure and tensile properties of high density two phase alloys 90W-7Ni-3Fe and 93W-4.9Ni-2.1Fe. Samples were liquid phase sintered under hydrogen and argon at 1480 degrees C for 30 min and then 15% cold rotary swaged. Measurement of microstructural parameters in the sintered and swaged samples showed that swaging slightly increased tungsten grain size in the longitudinal direction and slightly decreased tungsten grain size i...
Effects of polyamide 6 incorporation to the short glass fiber reinforced ABS composites: an interfacial approach
Ozkoc, G; Bayram, Göknur; Bayramli, E (2004-12-01)
The properties of 30 wt% short glass fiber (SGF) reinforced acrylonitrile-butadiene-styrene (ABS) terpolymer and polyamide 6 (PA6) blends prepared with extrusion were studied using the interfacial adhesion approach. Work of adhesion and interlaminar shear strength values were calculated respectively from experimentally determined interfacial tensions and short beam flexural tests. The adhesion capacities of glass fibers with different surface treatments of organosilanes were evaluated. Among the different s...
Effects of Montmorillonite Content and Maleic Anhydride Compatibilization on the Mechanical Behavior of Polylactide Nanocomposites
Sarı, Burcu (2016-08-01)
The aim of this study was to investigate the effects of montmorillonite (MMT) type nanoclay content and maleic anhydride (MA) grafted polylactide (PLA) copolymer compatibilization on the mechanical properties of PLA nanocomposites; compounded by twin-screw extrusion melt-mixing followed with injection molding for shaping of bulk specimens. Successively intercalated and exfoliated structures of the nanocomposites were observed by XRD and TEM analysis, including the chemical interactions by FTIR. Mechanical t...
Effect of surface treatment on electrical conductivity of carbon black filled conductive polymer composites
Koysuren, Ozcan; Yesil, Sertan; Bayram, Göknur (Wiley, 2007-06-05)
Two different types of surface modifiers, 3-aminopropyltriethoxysilane and formamide, were applied to carbon black (CB) particles to lower electrical resistivity of polymer composites prepared by treated CB. Two different matrices, low-density polyethylene and nylon 6, were chosen to compound with surface modified CB. Surface energy of CB was increased by adding amine or amide functional groups during surface treatment of CB. According to electron spectroscopy for chemical analysis (ESCA), chemical modifica...
Sorry the service is unavailable at the moment. Please try again later.
Citation Formats
IEEE
ACM
APA
CHICAGO
MLA
BibTeX
A. KANTARCIOGLU and Y. E. Kalay, “Effects of Al and Fe additions on microstructure and mechanical properties of SnAgCu eutectic lead-free solders,”
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
, pp. 79–84, 2014, Accessed: 00, 2020. [Online]. Available: https://hdl.handle.net/11511/32848.
Show/Hide Menu
Hide/Show Apps
Search
Login
You can transmit your request, problems about OpenMETU.