Qualitative and quantitative assessment of waste generation in a refrigerator-manufacturing plant based on a waste tree and mass balance

Date

2021-08-01

Author

Donmezoglu Olmez, Cansu
Aksoy, Ayşegül

Metadata

Show full item record

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

Item Usage Stats

111
views

0
downloads

In this study, wastes originating at each production station during refrigerator manufacturing were identified and classified based on a waste tree. A mass balance study revealed a total waste production factor of 0.046 kg/kg of a product of which 75.3%, 23.9%, and 0.8% were non-hazardous wastes (NHWs), packaging wastes (PWs), and hazardous wastes (HWs), respectively. Wastes produced during refrigerator manufacturing were grouped under 35 different waste codes. Waste codes that contributed more than 5% by weight were 15 02 02 (contaminated absorbent material), 15 01 10 (contaminated packaging), 16 02 13 (electronic cards), 07 02 14 (polyol) and 08 05 01 (isocyanates), 19 08 13 (treatment sludge), 16 02 15 (capacitors), and 13 01 13 (hydraulic oil) for HWs, 12 01 01 (ferrous metal), and 16 02 16 (components) for NHWs, and, finally, 15 01 03 (wooden), 15 01 01 (paper&cardboard), and 15 01 02 (plastic) for PWs over 5 years. Scrap costs were used as a surrogate to determine production stages that generated high amounts of metal and plastic wastes. Logarithmically, increasing and decreasing trends were observed for PWs and NHWs over the study period, respectively. HW amounts did not exhibit a statistically significant trend. Twenty-eight BATs (best available techniques) were identified that could be applied in refrigerator manufacturing for waste minimization and management. Among those, 8 of them were proposed for further improvement for waste management in the facility.

URI

https://hdl.handle.net/11511/92490

Journal

ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH

DOI

https://doi.org/10.1007/s11356-021-16015-6

Collections

Department of Environmental Engineering, Article

Suggestions

OpenMETU
Core

STATISTICAL PROCESS ANALYSIS IN BROILER FEED FORMULATION ALTI, M; OZILGEN, M (Wiley, 1994-09-01) Statistical analysis of broiler feed production was done with data obtained in an industrial plant in an attempt to characterise the causes of variations in feed composition. Analysis of the experimental data has shown that the feed conversion ratio (FCR) for broilers was between 1.8 and 2.5. This large range of observations were thought to be caused by the wide range of variations in the composition of the feeds. The major factor contributing to the variance of the feed compositions was the variance of the...
Modeling of alumina production for identification of solar hybridization paths Abu Zanouneh, Basil; Tarı, İlker (null; 2019-10-06) Bauxite to Alumina production processes of Seydisehir Aluminum Plant are investigated based on a previous study detailing the sub-processes and auditing the mass balances of the plant. The details of the balances are used to form a system model using Aspen Pro commercial software package. The mass balances of the system model are used for model validation by comparing them with the literature data. The validated model is used for determining the mass and energy flows together with the flow properties. Based...
Comparison of iscst3 and aermod air dispersion models: case study of cayirhan thermal power plant Dölek, Emre; Atımtay, Aysel; Department of Environmental Engineering (2007) In this study, emission inventory was prepared and pollutant dispersion studies were carried out for the area around Çayırhan Thermal Power Plant to determine the effects of the plant on the environment. Stack gas measurement results were used for the emissions from the power plant and emission factors were used for calculating the emissions from residential sources and coal stockpiles in the study region. Ground level concentrations of SO2, NOx and PM10 were estimated by using EPA approved dispersion model...
Geotechnical Assessment of Compacted Sand Bentonite Mixtures to be Utilized in Underground Nuclear Waste Repositories and Barrier Design Akgün, Haluk; Koçkar, Mustafa Kerem (2016-07-01) This study assesses the mechanical and hydrological performance of compacted sand bentonite mixtures to be utilized in sealing underground nuclear waste repositories. In order to assess the performance of this material and to obtain an optimum sand bentonite mixture, a variety of laboratory tests, namely, compaction, falling head permeability, swelling, unconfined compression and shear strength tests were performed on sand bentonite mixtures possessing bentonite contents ranging from 5% to 15%. Sand bentoni...
A Novel design and fabrication paradigm for 3D printers: LIPRO Haseltalab, Vahid; Yaman, Ulaş; Dölen, Melik; Department of Mechanical Engineering (2018) This study starts with highlighting some disadvantages of the conventional design and fabrication pipelines of Additive Manufacturing (AM) processes. In order to overcome the major drawbacks of the conventional pipeline, a novel design and fabrication pipeline called as LIPRO is proposed and it is implemented on two different AM processes to illuminate its effectiveness on alleviating the disadvantages of the conventional approaches. A single board computer is used to realize the method on AM machines. The ...

Citation Formats

C. Donmezoglu Olmez and A. Aksoy, “Qualitative and quantitative assessment of waste generation in a refrigerator-manufacturing plant based on a waste tree and mass balance,” ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH, pp. 0–0, 2021, Accessed: 00, 2021. [Online]. Available: https://hdl.handle.net/11511/92490.